Usually, the F1 code on an oven means that the control board has failed and that it has to be replaced. Sometimes you can solve the F1 code by cleaning, disconnecting, and reconnecting the ribbon connector from the ERC to the touchpad.
This, however, varies depending on the model and brand. Moreover, temperature sensors and key panels can cause F1 problems. It’s important to know what to do if your oven shows this code. It will save you money, effort, and time. And you may be able to address the problem entirely on your own at times.
What Does F1 Mean on the Oven
In most cases, the F1 error indicates that the oven’s electronics have failed. This problem can occur in the electronic oven control, the keypad, or the temperature sensor in the oven. Moreover, overheating of the thermostat can cause this error, as the oven’s sensors are unable to calibrate properly when the thermostat is not working properly. Data corruption in the electronic controller of the oven could also be the cause.
Generally, the user manuals describe a procedure to clear an F code. If those procedures don’t work, you will have to call an authorized service representative. But if you don’t have the user manual that came with your purchase, it will be difficult for you to understand the codes and troubleshoot the oven. And naturally, you turn to the internet.
How Do You Fix an F1 Oven?
The codes for different brands are different. Although some brands have the same codes, they each indicate a different problem. By no means are these codes universal. The meaning of each error code may also vary based on the model.
F1 Code on an LG oven
This can mean 2 things:
- The temperature sensor isn’t working properly
- A stuck button, a defective touchpad-to-control-board connection
When the temperature sensor isn’t working properly, it can show high ohms even when the oven isn’t on. This can also cause the oven to perform multiple tasks at the same time. After use, the oven will regulate the sensor circuit to ensure that it returns to 1050-1100 ohms. If it doesn’t go down, maybe that’s what’s causing the F1 code.
Make sure that your harness and sensor circuit are in good working order. If they work fine, the touchpad is most likely the source of the problem. Your keypad may have been washed with an ammonia-based cleaning product or exposed to moisture. This has the potential to short multiple circuits at the same time.
Remove the ribbon connector from the touchpad to the electronic range control and clear the F1 code. If the code is still visible with the touchpad disconnected, then it’s time to replace the electronic range control. But if the code does not appear, then the error code is caused by the touchpad.
F1 Code on a GE Oven
This means that your oven’s electronic range control has failed. The display panel used to configure temperatures and times is the electronic range control. You cannot use the oven as the buttons for configuring your oven’s settings will not be working properly.
You should turn off the oven when this error occurs. It’s best to unplug the oven just to be cautious. The electronic range control must be replaced to repair your GE oven.
F1 on a Thermador Oven
This means due to an oven control failure, you have to replace the control board. You can run a test to determine whether or not you need to replace the electronic range control. Only Thermador models without a built-in touchpad for electronic range control can be subjected to this test.
ERC and the touchpad must be two separate units. Turn off the oven. Disconnect the connector of the ERC and touchpad and reconnect it after fifteen minutes. Check for any loose wires.
Turn on the oven. To check if the code reappears, run the oven for at least an hour. If it doesn’t, you’re good to go.
F1 Code on an Amana Oven
You need to change the control board due to the control board failure. First, unplug the oven for ten minutes and plug it back in. Then you can replace the control board. This will restore the power supply of the oven as well as the control board’s memory.
If the error continues to appear after reconnecting the unit, contact a technician or customer care.
F1 on a Maytag Oven
This means that the control board clock or the touchpad is having issues. You can solve this problem by disconnecting the ribbon connector of the electronic range control and the keypad and cleaning it. Try soldering torn soldered connection. You can also try disconnecting and reconnecting the ribbon.
How Do I Fix F1 Error on Whirlpool Oven
F1 error on your Whirlpool oven can mean that there is an analog to digital failure. Unplug the range for 30 seconds and then plug it in. Or you can turn off the circuit. Examine and secure the connections to electronic components, including the control panel, mainboard, and keypad, while the oven is turned off.
You have to replace the control board if the same display reappears. An F1 reading could also indicate a shorted keypad or a faulty safety flip-flop, necessitating the replacement of the keypad or board.
How Do I Fix F1 Error on Stove
The F1 error on most stoves indicates that the control is not properly monitoring the temperature. You should unplug power for 30 to 60 seconds, then reapply power. If the F1 error shows again, replace the Electronic Oven Control (EOC).
What Does F1 Mean on An Electric Stove
The F1 code can mean one of the followings:
- Failed Electronic Oven Control (EOC)
- Shorted keypad which is part of the EOC
- The oven temperature sensor is not working properly
Frequently Asked Questions
How Do I Get My Oven to Stop Beeping?
You can try resetting the oven. Simply turn off the circuit breaker or unplug the oven. This should make the beeping stop. Or you can call a technician.
What does F1 on a Magic Chef Oven Mean?
It means that the oven has a defective control board or touchpad. You have to replace them if such an error occurs.
The F1 error on your oven means that the oven has experienced an electronic failure. It is safer to test the oven when it has cooled down, but you should monitor the oven until the code has gone away.
While it’s unlikely that the oven is overheating, the temperature sensors are having trouble regulating the temperature, or the elements are malfunctioning, unplugging the oven is still a good idea until you have more information about the situation.